Many older farm tractors have manual steering. On light work that is fine, but with heavy implements, loaders or tight turns, the effort can become tiring. Power steering can make a real difference, but it is a significant hydraulic modification to a steering system, so it is worth planning carefully and checking the results thoroughly.
How does power steering work on a tractor?
Power steering uses hydraulic pressure to help turn the wheels. A pump, usually driven by a belt or gear from the engine, supplies oil under pressure. A control valve, connected to the steering wheel, directs that oil to a cylinder that moves the wheels. The driver turns the wheel, the valve sends pressure to the cylinder, and the operator needs less effort. The amount of assistance depends on the system’s design and the pressure it runs at.
The two main approaches
There are two broad ways to add power steering to an older tractor:
- Power-assisted: a hydraulic cylinder helps the existing mechanical steering linkage. The steering box and linkage stay in place, so the mechanical connection to the wheels is kept. This is usually the less drastic change.
- Full hydraulic: a control valve routes fluid to double-acting cylinders that turn the wheels. There is no direct mechanical link from the steering wheel to the road wheels. This takes more changes to the tractor, and the operator gets less direct feedback through the wheel.
Each approach has different strengths. The right choice depends on how the tractor will be used, what space and mounting points you have, and how much you are willing to change.
Can I still steer without power steering?
With power-assisted steering, the mechanical linkage usually still steers the tractor if the hydraulics fail, although it will be much heavier to turn. With full hydraulic steering, a failure can leave you with much heavier steering or none at all, depending on the design. Ask the kit supplier directly what happens if the pump or a hose fails, and whether a mechanical backup exists. If the answer is unclear, do not proceed until it is.
Check the tractor before you buy a kit
Power assist changes how the steering system works, so worn parts matter more. Before you buy anything, check the existing steering components:
- Kingpins and bushings: look for play, wear and damage.
- Tie rods and drag link: check the ends for play and the threads for damage.
- Steering box or gear: look for play and leaks.
- Front axle and wheel bearings: check for wear that could show up as wander or play.
Replace worn parts before you add power assist. The conversion will not fix them, and a worn joint under hydraulic load is a safety problem.
Then check the rest of the system:
- Model and serial number: make sure the kit is designed for your tractor, not a similar one.
- Hydraulic supply: check whether the tractor has a pump drive and a reservoir that suit the system, and whether the flow and pressure are appropriate.
- Space and mounting points: check clearance around the steering column, pedals, fenders, linkage and the engine.
- Hoses and fittings: check their pressure ratings and routing. Cheap hoses and fittings are a common weak point.
- Manual: the service manual shows the steering geometry and hydraulic specifications to work from.
Installation outline
We do not give step-by-step installation here, because each kit and tractor differs. In general, the work involves mounting the pump and reservoir, fitting the valve and cylinder, routing and connecting the hoses, filling with the specified fluid, bleeding air from the system, and checking the steering geometry afterward. Follow the kit maker’s instructions and the service manual. If any part of the job is outside your skills, a hydraulics technician or dealer can do it.
Safety tests before driving
Steering is a safety system, so test thoroughly before the tractor goes on the road or into the field:
- Check every fitting, hose and joint for leaks with the engine off, then with the engine running at idle.
- Check the steering at a standstill. Turn the wheel lock to lock and make sure the stops work.
- Test the steering at low speed in an open area with no bystanders. Watch for pulling, wander, or any sudden change in effort.
- Confirm that the brakes work normally and that the steering responds the same way in both directions.
- Check the hydraulic relief and watch for overheating during extended turning.
- Recheck all fittings after the first few hours of use and again after the first full day.
If anything feels wrong, stop and find the cause before you continue.
Maintenance after conversion
Power steering adds a hydraulic system that needs regular checks. Look at the fluid level and condition, and check hoses for swelling, cracking and chafing. Listen for pump noise, and check the filter if the system has one. Replace old hoses on a schedule rather than waiting for them to fail. Keep the fluid clean, and use the type the kit or the service manual specifies.
When to get a hydraulics professional involved
If you are not comfortable with hydraulic systems, get a professional to do the work or at least to check it. The same applies if the tractor is used for heavy loads or is run in a setting where a steering fault could hurt someone. For the cost side of a conversion or repair, see How Much Will Power Steering Cost?
For the parts that make up the steering system, see What Are the Four Major Components of a Steering System? The service manual that matches your tractor is the best reference for specifications, so see where to find old tractor manuals if you do not have one.