An old tractor that has sat for years usually fails for simple reasons: stale fuel, a weak or fouled spark, a restricted air supply, or low compression. Work through the checks in a fixed order, and start with safety. Use the service manual’s specifications for every reading, and do not guess. Where a check needs a number, the manual is the source.
Safety before you start
- Chock the wheels, set the parking brake, disengage the PTO and lower any implements.
- Check that the guards are in place before you run the engine.
- Work outdoors or in a space with good airflow. Engine exhaust contains carbon monoxide, which can build up quickly in a closed building.
- Keep a fire extinguisher close by when you handle fuel, and never smoke near fuel.
- Do not work under a raised tractor unless it is supported on stands.
- Disconnect the battery before doing electrical work.
- Be careful with starting aids. Ether-based starting fluid is highly flammable, and using it the wrong way can damage an engine. Use it only as your manual describes.
Start with the basics
- Check the oil level, and the coolant level if the engine is water-cooled.
- If the tractor has electric starting, check the battery’s charge and its terminals.
- Look for obvious leaks of fuel, oil or coolant.
- Check the safety switches that prevent starting, such as the clutch or neutral switch, and make sure they work as designed.
- Find the decompression lever if your engine has one, and use it when cranking as the manual directs.
Check the fuel
Fuel problems are the most common reason a tractor will not start after storage.
- Stale gasoline. Old fuel forms varnish and gum. This blocks jets in the carburetor and clogs filters. If the tractor has been standing for a long time, drain the tank, the carburetor bowl and the lines, then refill with fresh fuel.
- Ethanol blends. Gasoline with ethanol can absorb water and degrade over time. A fuel stabilizer can help a tractor that will be stored, but it does not fix fuel that has already degraded.
- Clogged filters. Replace a dirty fuel filter. Check the fuel shut-off valve and the lines for blockages and cracks.
- Water in diesel. Water causes poor running and can damage injection parts. Drain water from the filter bowl if the tractor has one, and check the tank for water and sediment.
- Air in a diesel system. Air can prevent the engine from starting. Bleed the system following the service manual, because the procedure differs widely between engines.
Check the spark on gasoline engines
Many older tractors, especially gasoline models, use a magneto instead of a battery and coil. A magneto generates its own spark, so the battery and starter checks in modern troubleshooting guides may not apply. Check the manual to see which system your tractor uses.
On a magneto, start with the spark plug, then check the magneto’s timing and any points and condenser it has. Burnt or misadjusted points cause weak or missing spark. Check the spark plug lead, and the cap or distributor if the engine has one, for cracks and carbon tracking.
On a battery-and-coil system, check the battery, the coil, the points if fitted, and the plugs and leads.
Plug condition tells you a lot. A sooty plug often points to a rich mixture. An oily plug can point to worn rings or valve guides. A plug that is wet with fuel can mean the engine is flooded. Compare the plugs with the manual’s gap and type specification, and fit new plugs of the correct heat range if the old ones are worn.
Test the spark with a spark tester where you can. Keep your hands and face clear of the plug hole and the leads while the engine is cranked, and never hold a live lead.
Diesel engines: what to check instead
Diesel engines do not use spark ignition, so the spark checks above do not apply. For a diesel that will not start, focus on fuel delivery, air in the system and compression. Check that fuel reaches the injection pump, that the filter is clean, and that the system has been bled. If the engine has glow plugs or another cold-start aid, check those too. Injection pumps and injectors need specialist equipment and training, so take them to a qualified shop if they are faulty.
Check the air supply and carburetor
A dirty air filter restricts airflow and can make the engine hard to start or run poorly. Clean or replace the filter. Check the intake for cracks and leaks, because unmetered air upsets the mixture.
On gasoline engines, the carburetor is a frequent source of trouble after storage. Check the float level, clean any blocked jets and passages, and make sure the choke and throttle move freely. A sticking governor can also limit the throttle, so check its linkage.
Run a compression test
A compression test shows how well the cylinders seal. Fit a compression gauge in the spark plug hole (or the injector hole on a diesel). With the throttle open, crank the engine for the number of turns the manual specifies. Follow the service manual for the procedure and the specifications.
Compare the readings between cylinders, and look at the pattern. A large difference between cylinders often points to a valve, ring or head gasket problem in the weakest cylinder. Low readings across every cylinder can point to general wear, or to a problem with the test itself. Before you draw conclusions, check the gauge, the test conditions and the battery or starter, because weak cranking gives low readings.
Valve clearances
Valve clearances affect both compression and running. Too little clearance can leave a valve partly open, which causes poor compression and can burn the valve. Too much clearance causes noise and poor performance. Check and set the clearances to the service manual’s specification, in the condition the manual calls for. Recheck them after the first few hours of running.
Signs to stop and get help
- Metal particles in the oil, or a strong metallic smell
- Knocking that changes with load or engine speed
- Coolant in the oil, or oil in the coolant
- Smoke that is blue, white or black and does not clear
- A large difference in compression between cylinders
- Fuel or oil leaks that you cannot trace or fix
- Cracks in castings or the block
If you find any of these, stop running the engine. Continued running can turn a manageable repair into an expensive one.
Where to go next
- Where to Find Old Tractor Manuals explains how to get the specifications you need for each check.
- Repowering an Old Tractor covers when compression and wear point to an engine swap.
- Is an Old Tractor Worth Restoring? helps you decide whether the project is worth the cost before you spend money.