Restoration and Repair

What are the four major components of a steering system?

The four major components of a steering system: wheel and column, steering gear, linkage and front wheel assemblies, plus where power assist fits.

On this page
  1. The steering wheel and column
  2. The steering gear
  3. The linkage
  4. The front wheel assemblies
  5. Where power steering fits
  6. Signs of wear to check
  7. How to check your tractor’s steering
  8. Where to go next

A common way to group a tractor’s steering system is into four parts: the steering wheel and column, the steering gear, the linkage, and the front wheel assemblies. Power assist, where it is fitted, is an add-on that works alongside these parts.

No single official list exists. Sources group the parts in different ways, so treat this as one clear way to think about the system rather than a fixed rule.

The steering wheel and column

The steering wheel is the input. As you turn it, the steering column, also called the steering shaft, rotates and carries that motion to the steering gear. On many machines the column includes universal joints, which let it bend at an angle, so the wheel can sit where the operator needs it.

Wear here shows up as play in the wheel, meaning movement before the front wheels respond. A clunk when the wheel changes direction can point to a worn joint or a loose column.

The steering gear

The steering gear converts the rotation of the steering wheel into movement that turns the wheels. Three common designs are the rack and pinion, the recirculating ball and the worm and sector. Rack and pinion is the most common design in modern cars. Box-type gears such as the worm and sector and the recirculating ball are commonly found on older tractors and trucks.

Steering gears can be adjusted to take up play, and the service manual describes how to do it for your model. Adjust only as the manual describes, because setting a gear too tight can cause the steering to bind.

The linkage

The linkage carries the force from the steering gear out to the wheels. On a tractor it usually includes a drag link (sometimes called a relay rod), a pitman arm that connects to the steering gear, tie rods, and steering arms. Some designs also use an idler arm to support the linkage.

Each joint has a ball, bushing or pin that wears over time. Worn joints add play at the wheel and can make the tractor wander on a straight road.

The front wheel assemblies

The front wheel assemblies let the wheels pivot so the tractor can turn. Depending on the design, they include kingpins or spindles, steering arms and wheel bearings. Wear here can cause play, uneven tire wear and a tendency to pull to one side. Kingpins and their bushings are common wear points on older front axles.

Where power steering fits

Power steering adds a hydraulic pump, a control valve and one or more cylinders. In a power-assisted design, the cylinder helps the existing gear and linkage, so those parts still do their job. In a full hydraulic design, the cylinders take over most of the work of moving the wheels. Either way, the four parts above still have to be sound. For a closer look at adding assist, see Adding Power Steering to an Old Tractor.

Signs of wear to check

Watch for these signs before you put the tractor to heavy work:

  • Play at the steering wheel before the wheels move
  • Pulling to one side, or wandering on a straight road
  • Clunks or knocks when turning or going over bumps
  • Uneven or fast tire wear on the front
  • Stiffness or binding at one point in the turn

Any of these is worth checking before you rely on the steering.

How to check your tractor’s steering

With the tractor safely supported on stands and the engine off:

  1. Turn the steering wheel slowly from side to side, and note how far it moves before the front wheels respond.
  2. Grip each tie-rod end and each joint in the linkage, and feel for play.
  3. Check the kingpins or spindles for movement, and the wheel bearings for play.
  4. Check the steering stops, and look for damage or wear on the linkage.
  5. Compare what you find with the limits in the service manual, and replace worn parts before you use the tractor.

If you are unsure what you are seeing, have a qualified mechanic check the steering before heavy use.

Where to go next

The complete guide to restoration and repair

How to Restore a Vintage Tractor: A John Deere Restoration Walkthrough
Read the guide

Keep exploring

Guides from other topics

All topics →