International Harvester

International 240 Utility and 660 Tractors

Specs, history and buying notes for the International 240 Utility and 660 tractors, two IH models built from 1958 to 1963, with identification tips.

On this page
  1. International 240 Utility
  2. International 660
  3. Naming: Farmall or International
  4. Buying and restoring
  5. What they sell for
  6. Specs and manuals

The International 240 Utility and the International 660 were built for different jobs. The 240 Utility was a small, low-profile two-wheel-drive tractor for light utility work. The 660 was a heavy standard-tread tractor for large field and tillage work. Both have features that buyers should check before they buy.

International 240 Utility

The International 240 Utility was a compact, low-profile two-wheel-drive tractor built in Louisville, Kentucky, from 1958 to 1962. It was the utility version of the Farmall 240 row-crop tractor. The two shared much of the same drivetrain, but the Utility sat lower, with a lower center of gravity, a shorter wheelbase and a wide front axle. The Farmall 240 sat higher for row-crop clearance.

Key specifications, as listed in reference sources:

  • Engine: 2.0 L (123 cu in) four-cylinder gasoline, rated at about 38.5 gross hp. Sources put its output at roughly 29 to 32 hp at the drawbar or PTO.
  • Transmission: Four-speed sliding gear, according to sources. Confirm this in your manual.
  • Weight and wheelbase: Roughly 3,100 to 3,640 lb, depending on configuration and attachments. The wheelbase is 75 inches.
  • Hydraulics and hitch: Open-center hydraulics with up to two auxiliary valves, a rear 540 PTO, and IH Fast Hitch or two- or three-point hitch options.
  • Steering and brakes: Manual steering, or optional hydrostatic power steering. Independent mechanical disc brakes.
  • Electrical: Originally 6-volt. Many have been converted to 12-volt.

International 660

The International 660 was a heavy-duty standard-tread two-wheel-drive tractor built from 1959 to 1963. Sources list 6,945 units built and describe it as IH’s largest standard tractor of its era. It was designed for large-scale field and tillage work.

  • Engines: Six-cylinder engines were offered in gasoline, diesel and LP-gas versions. Owner references identify the gasoline engine as a 263 cubic-inch six (about 4.3 L) and the diesel as a 282 cubic-inch six (about 4.6 L).
  • Power: Nebraska tests quoted by owners recorded about 81 PTO hp for the gasoline version and about 79 PTO hp for the diesel. Sources disagree on the rated figure, so compare test results with care.
  • Engine speed: The 660 was rated at about 2,400 rpm. Its close relative, the 560, was rated at about 1,800 rpm.
  • Weight: About 9,600 to 9,900 lb, with an 85.5-inch wheelbase, according to TractorData.

The 660 shared much of its design with the 560, but it ran at higher engine speed and used taller clearances. Its drive used the same gearing as the 560, with added planetary reduction in the rear wheel hubs. That kept road speeds manageable at the higher engine speed.

Owner discussions describe several clutch and Torque Amplifier layouts across the 660’s production. Check your tractor’s controls against the manual before you order parts or assume a layout.

Octane Press reports that early 560 and 660 models had differential gear problems that led to a public recall. If you are looking at an early example, check the differential.

Naming: Farmall or International

The 240 Utility was the utility counterpart to the Farmall 240. The 660 was sold as an International, a standard-tread model, not a row-crop Farmall. In general, Farmall names meant row-crop models and International names meant standard-tread machines. Check the configuration on the tractor itself.

Buying and restoring

  • Electrical system. The 240 was originally 6-volt. Before converting to 12-volt, check the wiring and charging system. Keep the original parts if you want to keep the tractor original.
  • Torque Amplifier and controls. On a 660, confirm the clutch and Torque Amplifier layout against the manual.
  • Differential. On early 560 and 660 examples, check the differential, given the recall history.
  • Power steering. Some 240s had hydrostatic power steering. Check that it works.
  • Air cleaner. The 240 used an oil-bath air cleaner. Keep it serviced.

What they sell for

Listing ranges in the research put used 240 Utility tractors at about $1,800 to $5,000, depending on condition and attachments such as a front-end loader. These are asking prices, not sale prices. The research did not give a reliable price range for the 660, so compare recent auction results and listings for the same engine type and condition.

Specs and manuals

TractorData has full technical listings for both models, and TractorHouse tracks auction results. Manuals that cover the 560 and 660 are sold by reprint publishers. Check the serial range on any listing before you buy.

The complete guide to international harvester

International Harvester and McCormick Tractors: A Collector's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →