For tractors built since about 2008, the 10th character of the 17-character product identification number (PIN) gives the model year. Older machines do not use a single year code. For those, you match the model and serial number against a year-by-year chart. This guide explains where to find the serial plate, how to read the year code, and how to handle older numbers.
Where to find the serial plate
The plate’s location depends on the type of machine:
- Compact tractors (1 to 4 Series): On the right side of the frame, above the front axle.
- Large tractors (5 Series and up): On the right side of the frame, sometimes behind a panel or near the steps.
- Lawn tractors and zero-turn mowers: Under the seat or on the frame near the engine.
- Older tractors: Locations vary. For example, the plate on a 4430 is on the rear of the tractor, on the right side, above the PTO shaft.
The number may also be stamped into the frame in addition to the riveted plate. The engine has its own serial number, stamped on the engine block, and that number identifies the engine, not the tractor. Wipe the plate clean before you read it, because dirt and paint can hide digits.
Reading a 17-character PIN
On current equipment, the 10th character of the PIN is the model-year code. John Deere uses letters and digits in a cycle, and it does not use the letters I, O, Q, U, or Z. Some of the codes from the Deere operator’s manual are:
| Year | Code | Year | Code |
|---|---|---|---|
| 2008 | 8 | 2018 | J |
| 2009 | 9 | 2019 | K |
| 2010 | A | 2021 | M |
| 2011 | B | 2022 | N |
| 2012 | C | 2023 | P |
| 2013 | D | 2024 | R |
| 2014 | E | 2025 | S |
| 2015 | F | 2026 | T |
| 2016 | G | 2027 | V |
| 2017 | H |
The 2020 code is covered below, because the references disagree.
The model year can be one year ahead of the calendar year, because production for a new model year often starts in the fall of the year before. A tractor with a 2024 code may have been built late in 2023.
The 2020 code
Most decoders list the code for 2020 as L. One Deere operator’s manual table in our research lists it as E, which is also the code used for 2014. Check your operator’s manual, and a second decoder if you have one, before you rely on the 2020 code.
Older serial numbers (before 2008)
Older machines have shorter serial numbers that follow model-specific patterns, so there is no single year letter to read. Instead, look up the model and serial number in a year-by-year production chart. Serial number ranges start at a particular number for each year, so a number falls into the year whose starting number it is at or above, and below the next year’s starting number.
For example, collector references list these approximate starting serial numbers for the John Deere 70:
- 1953: 7000001
- 1954: 7006692
- 1955: 7017501
- 1956: 7034950
A 70 with a serial number between 7006692 and 7017500 would fall in 1954 on that chart. Treat these as approximate, and confirm them against a reference for your model before you rely on them. The John Deere 70 guide explains more about the model.
Missing or damaged plates
If the plate is missing or unreadable, try these options:
- Look for a stamped number on the frame rail, which some tractors have in addition to the plate.
- Check paperwork, such as the bill of sale, warranty card, or financing documents, which often list the serial number.
- Ask a dealer. A dealer’s parts department may be able to look up a number from a previous service record, or decode a number from a clear photo.
Why the serial number matters
The serial number tells you more than the model name. Deere can change components within a model across production years, so a part for one year may not fit another. The serial number also helps a buyer confirm the configuration, which affects value. The guide to the value of an antique John Deere explains how configuration and condition change the price.
For older machines, the classic John Deere tractors guide gives context on the models of each era, and the John Deere 4430 guide shows how one model’s plate location and configuration are documented.